WHY LEARNING PLUMBING BASICS IS VITAL FOR BATHTUB INSTALLATION

Why Learning Plumbing Basics is Vital for Bathtub Installation

Why Learning Plumbing Basics is Vital for Bathtub Installation

Blog Article

Book A Service

The publisher is making a few good pointers on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround in general in the article which follows.


Installing A Bathtub
Installing a bathtub isn't specifically brain surgery, but it does call for solid plumbing, carpentry, and also occasionally, tiling skills. Replacing an old bath tub with a brand-new one is also a reasonably tough project. If the old bathtub is readily accessible, the project can relocate quickly; if you need to open a wall surface to remove the old tub and also position the new tub, the job is much harder. In either instance, the project is within a house handyman's abilities, although you will certainly require a helper to leave the old tub and also embeded in the new one. Ensure you have actually certified on your own for the work as well as fit attempting it. As opposed to hiring a contractor to take over a halfway-completed task, it is far better to think about utilizing one prior to you start. Opportunities are you might require an expert plumber to make tube connections.
This post will help you install a new bath tub in your bathroom if you have actually already bought a brand-new bathtub as well as don't require to alter the setup of your previous water pipes.
Your tools and also material list must comprise the following:
  • New Bath tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipeline Caps


  • Getting ready for the Installment


    First of all, the sustaining frame provided with the bath ought to be fitted (if needed) according to the manufacturer's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is important to make certain that if the tap includes a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bath, it is additionally reasonable to fit a supporting plate under the faucets system to stop pressure on the bath tub.
    Fit the adaptable faucet ports to the bottom of the two faucets utilizing 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bath. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize every one of the supplied washing machines.
    Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to currently prepare to be fitted in its last placement.

    Removing Old Touches


    If you require to change old faucets with brand-new ones as a part of your installation, then the first thing you should do is detach the water. After doing so, turn on the faucets to drain pipes any kind of water staying in the system. The process of eliminating the existing faucets can be fairly troublesome due to the limited access that is often the case.
    Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipes to the faucets. Have a fabric prepared for the staying water that will certainly come from the pipelines. As soon as the supply pipelines have been gotten rid of, use the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from turning throughout this procedure. Once the faucets have been removed, the holes in the bath/basin will certainly need to be cleaned of any kind of old sealing compound.
    Before proceeding to fit the brand-new faucets, compare the pipe connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.

    Installing the Bath tub


    Using both wood boards under its feet, position the bath tub in the required setting. The wooden boards are useful in equally spreading out the weight of the bathtub over the area of the boards instead of focusing all the weight onto four tiny factors.
    The next objective is to make sure that the tub is leveled all round. This can be achieved by examining the spirit level as well as changing the feet on the tub until the level reads degree.
    To set up faucets, fit all-time low of the outermost adaptable tap port to the suitable supply pipeline by making a compression join; after that do the very same for the other faucet.
    Switch on the water supply and also check all joints and also brand-new pipework for leaks as well as tighten them if necessary. Fill the bath tub and also examine the overflow electrical outlet as well as the normal outlet for leaks.
    Finally, take care of the bathroom paneling as defined in the producer's user's manual. Tiling and also sealing around the tub must wait until the bath tub has actually been used at the very least when as this will certainly resolve it into its final position.

    Fitting New Touches


    If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic connector to stop damage to the string. One end of the adapter fits on the plastic tail of the faucet as well as the various other end gives a link to the existing supply pipes.
    If you require to fit a monobloc, after that you will call for reducing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
    Next, position the tap in the placing hole in the bath/basin ensuring that the washing machines are in location in between the tap as well as the sink. Protect the faucet in position with the producer supplied backnut. As soon as the faucet is securely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with normal faucet adapters. The former type needs to be linked to the faucet ends initially, tightening up only by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.

    Tiling Around the Tub


    In the location where the bath fulfills the floor tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the fitting can relocate enough to fracture a stiff seal, causing the water to permeate the wall in between the bath and also the tiling, causing issues with dampness and possible leaks to the ceiling listed below.
    You can select from a selection of coloured sealants to blend in your fixtures as well as installations. They are offered in tubes and also cartridges, and are capable of securing voids approximately a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to always fill the tub with water before securing, to allow for the activity experienced when the tub is in usage. The sealant can break rather early if you do not consider this motion prior to sealing.
    Alternatively, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise conveniently readily available on the market. It is suggested to fit the floor tiles utilizing water-resistant or water-proof sticky as well as grout.

    Bathtub Installation


    How Important Is A Bathtub To Your Home?


    High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.


    Install Piping Before Tub


    You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.


    Position the Tub


    Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.



    NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.


    Assemble Drain Connections


    Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.


    Place a Pipe For the Shower Head


    First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.


    Attaching Hot and Cold Water Lines


    Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.


    Install the Spout


    Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.



    NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.


    Check For Leaks


    Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.


    estore the Bathroom Wall


    Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

    https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    Hopefully you liked our section about Tools You Need to Install a New Bathtub . Thanks so much for spending some time to browse our content. Sharing is nice. Helping people is fun. We enjoy reading our article about How to Install a Bathtub Yourself.


    Request expert assessment.

    Report this page